OpenType font format
Tag:: dnom
Function:: Replaces selected figures which follow a slash with denominator figures. In the string 11/17 selected by the user, the application turns the 17 into denominators when the user applies the fraction feature.
Tag:: frac
Function:: Replaces figures separated by a slash with 'common' (diagonal) fractions. The user enters 3/4 in a recipe and gets the threequarters fraction.
Tag:: liga
Function:: Replaces a sequence of glyphs with a single glyph which is preferred for typographic purposes. This feature covers the ligatures which the designer/manufacturer judges should be used in normal conditions. The glyph for ffl replaces the sequence of glyphs f f l.
Tag:: numr
Function:: Replaces selected figures which precede a slash with numerator figures, and replaces the typographic slash with the fraction slash. In the string 11/17 selected by the user, the application turns the 11 into numerators, and the slash into a fraction slash when the user applies the fraction feature.
Tag:: sups
Function:: Replaces lining or oldstyle figures with superior figures (primarily for footnote indication), and replaces lowercase letters with superior letters (primarily for abbreviated French titles). The application can use this feature to automatically access the superior figures (more legible than scaled figures) for footnotes, or the user can apply it to Mssr to get the classic form.
Tag:: dlig
Function:: Replaces a sequence of glyphs with a single glyph which is preferred for typographic purposes. This feature covers those ligatures which may be used for special effect, at the user's preference. The glyph for ct replaces the sequence of glyphs c t, or U+322E (Kanji ligature for "Friday") replaces the sequence U+91D1 U+66DC U+65E5.
Tag:: zero
Function:: Some fonts contain both a default form of zero, and an alternative form which uses a diagonal slash through the counter. Especially in condensed designs, it can be difficult to distinguish between 0 and O (zero and capital O) in any situation where capitals and lining figures may be arbitrarily mixed. This feature allows the user to change from the default 0 to a slashed form. When setting labels, the user applies this feature to get the slashed 0.
Tag:: expt
Function:: Like the JIS78 Forms described above, this feature replaces standard forms in Japanese fonts with corresponding forms preferred by typographers. Although most of the JIS78 substitutions are included, the expert substitution goes on to handle many more characters. The user would invoke this feature to replace kanji character U+5516 with U+555E.
Tag:: fwid
Function:: Replaces glyphs set on other widths with glyphs set on full (usually em) widths. In a CJKV font, this may include "lower ASCII" Latin characters and various symbols. In a European font, this feature replaces proportionally-spaced glyphs with monospaced glyphs, which are generally set on widths of 0.6 em. The user may invoke this feature in a Japanese font to get full monospaced Latin glyphs instead of the corresponding proportionally-spaced versions.
Tag:: hwid
Function:: Replaces glyphs on proportional widths, or fixed widths other than half an em, with glyphs on half-em (en) widths. Many CJKV fonts have glyphs which are set on multiple widths; this feature selects the half-em version. There are various contexts in which this is the preferred behavior, including compatibility with older desktop documents. The user may replace a proportional Latin glyph with the same character set on a half-em width.
Tag:: jp78
Function:: This feature replaces default (JIS90) Japanese glyphs with the corresponding forms from the JIS C 6226-1978 (JIS78) specification. The user would invoke this feature to replace kanji character U+5516 with U+555E.
Tag:: pwid
Function:: Replaces glyphs set on uniform widths (typically full or half-em) with proportionally spaced glyphs. The proportional variants are often used for the Latin characters in CJKV fonts, but may also be used for Kana in Japanese fonts. The user may invoke this feature in a Japanese font to get a proportionally-spaced glyph instead of a corresponding half-width Roman glyph or a full-width Kana glyph.
Tag:: trad
Function:: Replaces 'simplified' Chinese hanzi or Japanese kanji forms with the corresponding 'traditional' forms. The user inputs U+53F0 and is offered a choice of U+6AAF, U+81FA, or U+98B1.
Tag:: vert
Function:: Replaces default forms with variants adjusted for vertical writing when in vertical writing mode. While most CJKV glyphs remain vertical when set in vertical writing mode, some take a different form (usually rotated and repositioned) for this purpose. Glyphs covered by this feature correspond to the set normally rotated in low-end DTP applications. In vertical writing mode, the opening parenthesis (U+FF08) is replaced by the rotated form (U+FE35).
Tag:: vrt2
Function:: Replaces some fixed-width (half-, third- or quarter-width) or proportional-width glyphs (mostly Latin or katakana) with forms suitable for vertical writing (that is, rotated 90 degrees clockwise). Note that these are a superset of the glyphs covered in the vert table. ATM/NT 4.1 and the Windows 2000 OTF driver impose the following requirements for an OpenType font with CFF outlines to be used for vertical writing: the vrt2 feature must be present in the GSUB table, it must comprises a single lookup of LookupType 1 and LookupFlag 0, and the lookup must have a single subtable. The predecessor feature, vert, is ignored. A rotated glyph must be designed such that its top side bearing and vertical advance as recorded in the Vertical Metrics ('vmtx') table are identical to the left side bearing and horizontal advance, respectively, of the corresponding upright glyph as recorded in the Horizontal Metrics ('hmtx') table. (The horizontal advance of the rotated glyph may be set to any value, since the glyph is intended only for vertical writing use. The vendor may however set it to head.unitsPerEm, to prevent overlap during font proofing tests, for example.) Thus, proportional-width glyphs with rotated forms in the vrt2 feature will appear identically spaced in both vertical and horizontal writing. In order for kerning to produce identical results as well, developers must ensure that the Vertical Kerning (vkrn) feature record kern values between the rotated glyphs that are the same as kern values between their corresponding upright glyphs in the Kerning (kern) feature. Proportional- or half-width Latin and half-width katakana characters are rotated 90 degrees clockwise for vertical writing.
Tag:: nalt
Function:: Replaces default glyphs with various notational forms (e.g. glyphs placed in open or solid circles, squares, parentheses, diamonds or rounded boxes). In some cases an annotation form may already be present, but the user may want a different one. The user invokes this feature to get U+3200 (the circled form of 'ga') from U+3131 (hangul 'ga').
Languages
Tag:: Japanese
Function:: These fonts support the Japanese script. Each font is Unicode™ encoded, and available in different formats. Please review the product information for each font to ensure it will meet your requirements.
$500
OpenType font format
Languages
Tag:: Japanese
Function:: These fonts support the Japanese script. Each font is Unicode™ encoded, and available in different formats. Please review the product information for each font to ensure it will meet your requirements.
$900 Select Format