Access All Alternates

Tag: aalt

Function: This feature makes all variations of a selected character accessible. This serves several purposes: An application may not support the feature by which the desired glyph would normally be accessed; the user may need a glyph outside the context supported by the normal substitution, or the user may not know what feature produces the desired glyph. Since many-to-one substitutions are not covered, ligatures would not appear in this table unless they were variant forms of another ligature. A user inputs the P in Poetica, and is presented with a choice of the four standard capital forms, the eight swash capital forms, the initial capital form and the small capital form.

Case-Sensitive Forms

Tag: case

Function: Shifts various punctuation marks up to a position that works better with all-capital sequences or sets of lining figures; also changes oldstyle figures to lining figures. By default, glyphs in a text face are designed to work with lowercase characters. Some characters should be shifted vertically to fit the higher visual center of all-capital or lining text. Also, lining figures are the same height (or close to it) as capitals, and fit much better with all-capital text. The user selects a block of text and applies this feature. The dashes, bracketing characters, guillemet quotes and the like shift up to match the capitals, and oldstyle figures change to lining figures.

Fractions

Tag: frac

Function: Replaces figures separated by a slash with 'common' (diagonal) fractions. The user enters 3/4 in a recipe and gets the threequarters fraction.

Standard Ligatures

Tag: liga

Function: Replaces a sequence of glyphs with a single glyph which is preferred for typographic purposes. This feature covers the ligatures which the designer/manufacturer judges should be used in normal conditions. The glyph for ffl replaces the sequence of glyphs f f l.

Ordinals

Tag: ordn

Function: Replaces default alphabetic glyphs with the corresponding ordinal forms for use after figures. One exception to the follows-a-figure rule is the numero character (U+2116), which is actually a ligature substitution, but is best accessed through this feature. The user applies this feature to turn 2.o into 2.o (abbreviation for secundo).

Scientific Inferiors

Tag: sinf

Function: Replaces lining or oldstyle figures with inferior figures (smaller glyphs which sit lower than the standard baseline, primarily for chemical or mathematical notation). May also replace lowercase characters with alphabetic inferiors. The application can use this feature to automatically access the inferior figures (more legible than scaled figures).

Superscript

Tag: sups

Function: Replaces lining or oldstyle figures with superior figures (primarily for footnote indication), and replaces lowercase letters with superior letters (primarily for abbreviated French titles). The application can use this feature to automatically access the superior figures (more legible than scaled figures) for footnotes, or the user can apply it to Mssr to get the classic form.

Tabular Figures

Tag: tnum

Function: Replaces figure glyphs set on proportional widths with corresponding glyphs set on uniform (tabular) widths. Tabular widths will generally be the default, but this cannot be safely assumed. Of course this feature would not be present in monospaced designs. The user may apply this feature to get oldstyle figures to align vertically in a column.

Small Capitals From Capitals

Tag: c2sc

Function: Small Capitals From Capitals

Small Capitals

Tag: smcp

Function: This feature turns lowercase characters into small capitals. This corresponds to the common SC font layout. It is generally used for display lines set in Large & small caps, such as titles. Forms related to small capitals, such as oldstyle figures, may be included. The user enters text as mixed capitals and lowercase, and gets Large & small cap text.

Historical Forms

Tag: hist

Function: Some letterforms were in common use in the past, but appear anachronistic today. The best-known example is the long form of s; others would include the old Fraktur k. Some fonts include the historical forms as alternates, so they can be used for a 'period' effect. This feature replaces the default (current) forms with the historical alternates. While some ligatures are also used for historical effect, this feature deals only with single characters. The user applies this feature in Adobe Jenson to get the archaic forms of M, Q and Z.

Titling

Tag: titl

Function: This feature replaces the default glyphs with corresponding forms designed specifically for titling. These may be all-capital and/or larger on the body, and adjusted for viewing at larger sizes. The user applies this feature in Adobe Garamond to get the titling caps.

Ornaments

Tag: ornm

Function: This is a dual-function feature, which uses two input methods to give the user access to ornament glyphs (e.g. fleurons, dingbats and border elements) in the font. One method replaces the bullet character with a selection from the full set of available ornaments; the other replaces specific "lower ASCII" characters with ornaments assigned to them. The first approach supports the general or browsing user; the second supports the power user. The user inputs qwwwwwwwwwe to form the top of a flourished box in Adobe Caslon, or inputs the bullet character, then chooses the thistle dingbat.

Discretionary Ligatures

Tag: dlig

Function: Replaces a sequence of glyphs with a single glyph which is preferred for typographic purposes. This feature covers those ligatures which may be used for special effect, at the user's preference. The glyph for ct replaces the sequence of glyphs c t, or U+322E (Kanji ligature for "Friday") replaces the sequence U+91D1 U+66DC U+65E5.

Initial Forms

Tag: init

Function: Replaces glyphs at the beginnings of words with alternate forms designed for this use. This is common in Latin connecting scripts, and required in various non-Latins like Arabic. In the typeface Ex Ponto, the default t in the word 'type' is replaced with the t.begin form.

Terminal Forms

Tag: fina

Function: Replaces glyphs at the ends of words with alternate forms designed for this use. This is common in Latin connecting scripts, and required in various non-Latins like Arabic. In the typeface Poetica, the default e in the word 'type' is replaced with the e.end form.

Capital Spacing

Tag: cpsp

Function: Globally adjusts inter-glyph spacing for all-capital text. Most typefaces contain capitals and lowercase characters, and the capitals are positioned to work with the lowercase. When capitals are used for words, they need more space between them for legibility and esthetics. This feature would not apply to monospaced designs. Of course the user may want to override this behavior in order to do more pronounced letterspacing for esthetic reasons. The user sets a title in all caps, and the Capital Spacing feature opens the spacing.

Kerning

Tag: kern

Function: Adjusts amount of space between glyphs, generally to provide optically consistent spacing between glyphs. Although a well-designed typeface has consistent inter-glyph spacing overall, some glyph combinations require adjustment for improved legibility. Besides standard adjustment in the horizontal direction, this feature can supply size-dependent kerning data via device tables, "cross-stream" kerning in the Y text direction, and adjustment of glyph placement independent of the advance adjustment. Note that this feature may apply to runs of more than two glyphs, and would not be used in monospaced fonts. Also note that this feature does not apply to text set vertically. The o is shifted closer to the T in the combination "To."

These fonts support the Basic Latin character set. Each font is Unicode™ encoded, and available in d

Tag: Basic Latin

Function: These fonts support the Basic Latin character set. Each font is Unicode™ encoded, and available in different formats. Please review the product information for each font to ensure it will meet your requirements.

These fonts support the Latin Extended character set. Each font is Unicode™ encoded, and available i

Tag: Latin Extended

Function: These fonts support the Latin Extended character set. Each font is Unicode™ encoded, and available in different formats. Please review the product information for each font to ensure it will meet your requirements.

Tag: lowercase

Function:

Tag: uppercase

Function: